Want to Pass 70-680 Exam In Next HOURS? Get it now →
October 11, 2017

A Complete Guide to 70 680 practice test

Accurate of 70 680 pdf braindumps materials and discount pack for Microsoft certification for examinee, Real Success Guaranteed with Updated exam 70 680 pdf dumps vce Materials. 100% PASS TS:Windows 7,Configuring exam Today!

Q121. - (Topic 3) 

You have a computer that runs Windows 7. 

You install Windows XP in a new partition on the computer and discover that you can no longer start Windows 7. 

You need to start Windows 7 in the minimum amount of time. 

What should you do? 

A. From Windows XP, modify the default path in the boot.ini file. 

B. From Windows XP Recovery Console, run the Fixboot command. 

C. Start the computer from the Windows 7 installation media and select Install now. 

D. Start the computer from the Windows 7 installation media and run Startup Repair. 

Answer:

Explanation: When configuring a new computer to boot between multiple operating systems, it is also necessary to install operating systems in the order that they were released. For example, if you want to boot between Windows XP and Windows 7 on a new computer, you need to install Windows XP before you install Windows 7. If you install Windows XP after Windows 7, the Windows XP installation routine cannot recognize the Windows 7 operating system installation and the computer only boots into Windows XP. It is possible to repair the computer from this point using Windows 7 startup repair so that it dual-boots, but the simplest course of action is just to install the operating systems in the order in which they were released 


Q122. - (Topic 3) 

You have a computer named Computer1 that runs Windows 7. You have a server named Server1 that runs Windows Server 2008. 

Computer1 and Server1 have IPv4 and IPv6 installed. 

You need to identify whether you can connect to Server1 by using IPv6. 

What should you do? 

A. Run Ping Server1 -6. 

B. Run Ping Server1- n 6. 

C. Run Net view \\\\Server1. 

D. Open \\\\server1 from the Run dialog box. 

Answer:

Explanation: 

Ping The Ping tool is still widely used, although more firewalls block Internet Control Message Protocol (ICMP) echo requests than used to be the case. However, even if you cannot get past a firewall on your organization's network, Ping is still useful. You can check that the IPv4 protocol is working on a computer by entering ping 127.0.0.1. You can then ping the IPv4 address of the computer. You can find out what this is by using the Ipconfig tool. If your computer has more than one interface combined in a network bridge, you can ping the Ipv4 address of the network bridge. When you have established that you can ping your computer using an Ipv4 address, you can test that DNS is working internally on your network (assuming you are connected to a DNS server, a WAP, or have ICS configured on your network) by pinging your computer name—for example, entering ping canberra. Note that if DNS is not implemented on your system, ping canberra still works because the IPv6 link-local address resolves automatically. -6 Force using IPv6. 


Q123. - (Topic 6) 

You are a network administrator for a global company that has Windows Server 2008 R2 servers and Windows 7 Enterprise computers. 

Management wants to decrease VPN costs by implementing DirectAccess for remote network access. 

They assign you to evaluate the current network infrastructure, which includes the following elements: 

Active Directory 

IPv6 network and applications 

Server for DirectAccess service 

You need to ensure that all critical infrastructure components are present. 

What should you add to the infrastructure? 

A. Windows Internet Name Service (WINS) server 

B. Public key infrastructure 

C. NAT-PT devices 

D. Windows Software Update Services (WSUS) server 

Answer:

Explanation: DirectAccess With Windows Server 2008 R2 requires: 

* Public key infrastructure (PKI) to issue computer certificates. 

* One or more DirectAccess servers running Windows Server 2008 R2 with two network adapters: one that is connected directly to the Internet, and a second that is connected to the intranet. 

* On the DirectAccess server, at least two consecutive, public IPv4 addresses assigned to the network adapter that is connected to the Internet. 

* DirectAccess clients running Windows 7 or Windows 8 "Enterprise" edition clients 

* At least one domain controller and Domain Name System (DNS) server running Windows Server 2008 SP2 or Windows Server 2008 R2. 


Q124. - (Topic 4) 

Your company network includes client computers that have Windows 7 installed. The computers are members of an Active Directory domain and receive Windows Firewall configuration through Group policy. 

A user indicates that he is unable to connect to a remote FTP server. 

You need to view the status of TCP/UDP ports at the user's computer. 

Which command should you run? 

A. netstat -o 

B. netstat -a 

C. ipconfig /all 

D. netstat –an 

Answer:


Q125. - (Topic 3) 

A user named User1 uses a shared computer that runs Windows 7. 

User1 is a standard user. User1 attempts to connect a USB device to the computer and is prompted to enter administrative credentials. 

You need to ensure that User1 can use the USB device without requiring administrative credentials. 

What should you do first? 

A. Add User1 to the Power Users group. 

B. Run Pnputil.exe and specify the - i- a parameters. 

C. Run Driverquery.exe and specify the /SI parameter. 

D. Copy the driver files to the C:\\windows\\system32 folder. 

Answer:

Explanation: 

When a driver is staged, it is placed in the device driver store and non-administrators can install the device, provided they have permission to install devices in the appropriate device setup class. Pnputil.exe is a command line utility that you can use to manage the driver store. You can use Pnputil to add driver packages, remove driver packages, and list driver packages that are in the store. -i Specifies to install the identified INF file. Cannot be used in conjunction with the -f parameter. 

Example pnputil.exe -i -a a:\\usbcam\\USBCAM.INF Adds and installs the specified driver 


Q126. - (Topic 6) 

You have an answer file named Unattend.xml for a Windows 7 automated installation. 

You need to perform an unattended installation of Windows 7 by using the answer file. 

What should you do? 

A. Name the answer file as unattend.xml and save it to a floppy disk. Start the computer from the Windows Preinstallation Environment (WinPE). 

B. Name the answer file as unattend.xml and save it to a USB disk. Start the computer from the Windows Preinstallation Environment (WinPE). 

C. Name the answer file as autounattend.xml and save it to a floppy disk. Start the computer from the Windows 7 DVD. 

D. Name the answer file as autounattend.ini and save it to a floppy disk. Start the computer from the Windows 7 DVD. 

Answer:

Explanation: Unattended installation You can perform an unattended installation of Windows 7 by using an installation file called Unattend.xml. These installation files store answers to the questions asked by the Setup Wizard. When the Windows 7 installation process starts, Windows checks for attached USB storage devices that have this file in their root directory. Unattended installations are suitable when you need to deploy Windows 7 to a large number of computers because you do not have to interact with them manually, responding to prompts, as the installation progresses.Building a Reference Installation You configure your reference computer with a customized installation of Windows 7 that you then duplicate onto one or more destination computers. You can create a reference installation by using the Windows product DVD and (optionally) the answer file you created in the previous section. To install your reference computer using an answer file, perform the following procedure: 

1. Turn on the reference computer. Insert the Windows 7 product DVD and the UFD containing the answer file (Autounattend.xml) that you created in the previous section. Note that the use of an answer file is optional, although it is the method Microsoft recommends. If you prefer, you can install Windows 7 manually from the installation DVD-ROM. 

2. Restart the computer by pressing CTRL+ALT+DEL. You may have to override the boot order to boot from the CD/DVD-ROM disk. If so, select the appropriate function key to override the boot order during initial boot. Windows Setup (Setup.exe) starts automatically and searches the root directory of all removable media for an answer file called 

Autounattend.xml. 

3. After Setup finishes, you can validate that all customizations were applied. For example, if you included the optional Microsoft-Windows-IE-InternetExplorer feature and set the Home_Page setting in your answer file, you can verify these settings by opening Internet Explorer. 

4. To prepare the reference computer for the user, you use the Sysprep utility with the /generalize option to remove hardware-specific information from the Windows installation and the /oobe option to configure the computer to boot to Windows Welcome upon the next restart. 


Q127. - (Topic 4) 

Your company has a main office and a branch office. 

A portable computer runs Windows 7. On the computer, you can configure a printer for each office. 

You need to configure printing on the computer to meet the following requirements: 

. When you are located in the main office, all documents must automatically print to the main office printer. . When you are located in the branch office, all documents must automatically print to the branch office printer. 

What should you do? 

A. From Location and Other Sensors, configure a default location. 

B. From Devices and Printers, configure the Manage Default Printer settings. 

C. From Region and Language, modify the Location settings. 

D. From Network and Sharing Centre, configure the network location. 

Answer:

Explanation: 

http://windows.microsoft.com/en-GB/windows7/Automatically-switch-default-printers-between-home-work-orschool 


Q128. HOTSPOT - (Topic 6) 

A law firm's wireless network does not use IPv6 and provides IP addresses automatically to connected clients. 

A visiting attorney arrives to perform a deposition. The attorney's computer has never connected to the firm's wireless network. The attorney needs general access to several websites but is unable to connect to the Internet. 

You collect information from the computer's Device Manager, Network Connections, and Wireless Network Connections. 

Device information is shown in the Device Manager exhibit. (Click the Exhibit button.) 

Network information is shown in the Network Connections exhibit. (Click the Exhibit button.) 

Wireless network information is shown in the Wireless Network Connections exhibit. (Click the Exhibit button.) 

You need to configure this attorney's laptop so it can access the Internet through the firm's wireless network. 

Consider each of the following statements. Does the information in the three screenshots support the inference as stated? (This question is worth three points.) 

Answer: 


Q129. - (Topic 4) 

You have a computer that runs Windows 7. 

You need to record when an incoming connection is allowed through Windows firewall. 

What should you do? 

A. In Local Group Policy, modify the audit policy. 

B. In Local Group Policy, modify the system audit policy. 

C. From the Windows Firewall with Advanced Security properties, set the logging settings to Log successful connections. 

D. From the Windows Firewall with Advanced Security properties, set the Data Protection (Quick Mode) IPSec settings to Advanced. 

Answer:

Explanation: 

Customize Logging Settings for a Firewall Profile Windows Firewall with Advanced Security can be configured to log events that indicate the successes and failures of its processes. The logging settings involve two groups of settings: settings for the log file itself and settings that determine which events the file will record. The settings can be configured separately for each of the firewall profiles. You can specify where the log file will be created, how big the file can grow, and whether you want the log file to record information about dropped packets, successful connections, or both. Log successful connectionsUse this option to log when Windows Firewall with Advanced Security allows an inbound connection. The log records why and when the connection was formed. Look for entries with the word ALLOW in the action column of the log. 


Q130. - (Topic 3) 

You deploy a Windows 7 Enterprise image to a computer on the network. 

You need to display the detailed activation and license status of the computer. 

What should you run? 

A. Msconfig.exe 

B. Slui.exe 

C. Slmgr.vbs and specify the dli parameter 

D. Winrm.vbs and specify the id parameter 

Answer:

Explanation: 

Slmgr.vbs /dli [Activation ID | All]Display license information. By default, /dli displays the license information for the installed active Windows edition. Specifying the [Activation ID] parameter displays the license information for the specified edition associated with that Activation ID. Specifying the [All] as the parameter will display all applicable installed products' license information. This operation does not require elevated privileges. 



see more free 70-680 exam dumps