Want to Pass NSE4 Exam In Next HOURS? Get it now →
April 20, 2017

Resources to nse4 dumps

Q51. - (Topic 17) 

Which statement is one disadvantage of using FSSO NetAPI polling mode over FSSO Security Event Log (WinSecLog) polling mode? 

A. It requires a DC agent installed in some of the Windows DC. 

B. It runs slower. 

C. It might miss some logon events. 

D. It requires access to a DNS server for workstation name resolution. 

Answer:


Q52. - (Topic 21) 

Which statements are true regarding IPv6 anycast addresses? (Choose two.) 

A. Multiple interfaces can share the same anycast address. 

B. They are allocated from the multicast address space. 

C. Different nodes cannot share the same anycast address. 

D. An anycast packet is routed to the nearest interface. 

Answer: A,D 


Q53. - (Topic 6) 

What is IPsec Perfect Forwarding Secrecy (PFS)?. 

A. A phase-1 setting that allows the use of symmetric encryption. 

B. A phase-2 setting that allows the recalculation of a new common secret key each time the session key expires. 

C. A ‘key-agreement’ protocol. 

D. A ‘security-association-agreement’ protocol. 

Answer:


Q54. - (Topic 16) 

Review the IPS sensor filter configuration shown in the exhibit 

Based on the information in the exhibit, which statements are correct regarding the filter? (Choose two.) 

A. It does not log attacks targeting Linux servers. 

B. It matches all traffic to Linux servers. 

C. Its action will block traffic matching these signatures. 

D. It only takes effect when the sensor is applied to a policy. 

Answer: C,D 


Q55. - (Topic 15) 

Review the IPsec phase 1 configuration in the exhibit; then answer the question below. 

Which statements are correct regarding this configuration? (Choose two.) 

A. The remote gateway address on 10.200.3.1. 

B. The local IPsec interface address is 10.200.3.1. 

C. The local gateway IP is the address assigned to port1. 

D. The local gateway IP address is 10.200.3.1. 

Answer: A,C 


Q56. - (Topic 13) 

Which statements are correct for port pairing and forwarding domains? (Choose two.) 

A. They both create separate broadcast domains. 

B. Port Pairing works only for physical interfaces. 

C. Forwarding Domain only applies to virtual interfaces. 

D. They may contain physical and/or virtual interfaces. 

Answer: A,D 


Q57. - (Topic 22) 

Which is one of the conditions that must be met for offloading the encryption and decryption of IPsec traffic to an NP6 processor? 

A. No protection profile can be applied over the IPsec traffic. 

B. Phase-2 anti-replay must be disabled. 

C. Both the phase 1 and phases 2 must use encryption algorithms supported by the NP6. 

D. IPsec traffic must not be inspected by any FortiGate session helper. 

Answer: C


Q58. - (Topic 22) 

Which statements are true about offloading antivirus inspection to a Security Processor (SP)? (Choose two.) 

A. Both proxy-based and flow-based inspection are supported. 

B. A replacement message cannot be presented to users when a virus has been detected. 

C. It saves CPU resources. 

D. The ingress and egress interfaces can be in different SPs. 

Answer: B,C 


Q59. - (Topic 6) 

An administrator wants to create an IPsec VPN tunnel between two FortiGate devices. 

Which three configuration steps must be performed on both units to support this scenario? (Choose three.) 

A. Create firewall policies to allow and control traffic between the source and destination IP addresses. 

B. Configure the appropriate user groups to allow users access to the tunnel. 

C. Set the operating mode to IPsec VPN mode. 

D. Define the phase 2 parameters. 

E. Define the Phase 1 parameters. 

Answer: A,D,E 


Q60. - (Topic 1) 

Which statements are true regarding the factory default configuration? (Choose three.) 

A. The default web filtering profile is applied to the first firewall policy. 

B. The ‘Port1’ or ‘Internal’ interface has the IP address 192.168.1.99. 

C. The implicit firewall policy action is ACCEPT. 

D. The ‘Port1’ or ‘Internal’ interface has a DHCP server set up and enabled (on device models that support DHCP servers). 

E. Default login uses the username: admin (all lowercase) and no password. 

Answer: B,D,E 



see more free NSE4 exam dumps